🌊 Plastica iFlo Pool Pump – 0.75HP (0.56kW) Single Phase | Self-Priming Circulation Pump

Affordable Excellence – Half the Price, Full Performance

The Plastica iFlo 0.75HP Pool Pump delivers exceptional reliability and performance without the premium price tag. Engineered specifically for swimming pools, this self-priming pump combines a heavy-duty air-cooled motor with a robust pump casing to ensure years of trouble-free operation.

With a virtually zero failure rate and proven track record, the iFlo pump is trusted by pool owners who demand dependable performance at an unbeatable value. Its oversized strainer basket and high-efficiency impeller keep your pool water crystal clear, properly circulated, and inviting for swimmers.

Whether you’re maintaining an above-ground pool, small in-ground installation, or need reliable circulation for your pool heating system, the iFlo delivers consistent, efficient performance season after season.

🌟 Key Features & Benefits

✅ Proven Reliability You Can Trust

Virtually zero failure rate backed by thousands of installations. Built with premium components and rigorous quality control, the iFlo pump delivers consistent performance season after season, giving you complete peace of mind.

✅ Outstanding Value for Money

Less than half the price of comparable pool pumps from premium brands, without compromising on quality, reliability, or performance. Get professional-grade circulation at a budget-friendly price that won’t break the bank.

✅ Simple to Install

Straightforward installation with standard 1.5″ (38mm) suction and delivery connections that fit most pool plumbing systems. Clear instructions and accessible components make setup quick and hassle-free for installers and experienced DIYers.

✅ Ultra-Quiet Operation

Engineered for whisper-quiet performance that won’t disturb your outdoor living space. Advanced motor design and vibration-dampening construction ensure peaceful pool enjoyment without annoying pump noise.

✅ Built to Last

Heavy-duty air-cooled motor and robust thermoplastic pump casing engineered for long-term durability. Resistant to pool chemicals, UV exposure, and harsh outdoor conditions.

✅ Self-Priming Design

Quick and easy priming with minimal effort. Simply fill the pump chamber with water, and the self-priming impeller handles the rest – no manual bleeding required.

✅ Oversized Strainer Basket

Large-capacity debris basket captures leaves, dirt, and debris before they reach the impeller. Fewer cleaning interruptions and better protection for your pump’s internal components.

✅ Easy Maintenance

Tool-free transparent cover access makes strainer basket cleaning quick and hassle-free. Spend less time on maintenance and more time enjoying your pool.

✅ Versatile Applications

Perfect for filtration, circulation, pool heating systems, and water features. Suitable for both residential and light commercial pool installations.

📊 Complete Technical Specifications

Specification	Detail
Brand	Plastica
Model	iFlo Series
Power Type	Single Phase
Horsepower	0.75 HP
Power Rating	0.56 kW
Motor Type	Air-cooled, heavy-duty with thermal protection
Pump Type	Self-priming centrifugal
Suction Connection	1.5″ (38mm)
Delivery Connection	1.5″ (38mm)
Maximum Water Temperature	35°C (95°F)
Priming Type	Self-priming
Noise Level	Ultra-quiet operation
Strainer Basket	Oversized capacity
Cover Type	Transparent for easy inspection
Installation Position	Horizontal mounting required
Base	Reinforced mounting base included
Drain Plug	Yes (for winterization)
Thermal Protection	Built-in motor thermal cutout
Electrical Protection Required	RCD (30mA residual current device)
Cable Type Required	H07 RN-F, 3 x 1mm²
Safety Standards	EN 60335-1, EN 60335-2-41
Compliance	CE marked, EMC 2004/108/EC, Low Voltage 2006/95/EC
Environmental	WEEE 2002/96/EC, RoHS 2002/95/EC compliant

🛡️ Comprehensive Warranty Coverage

Your iFlo pump is backed by comprehensive warranty protection for peace of mind:

Component	Warranty Period
Pump Body	2 Years
Motor	1 Year
Pump Seal	1 Year
Overall Coverage	1 Year Full Warranty

What’s Covered:

• Manufacturing defects in materials and workmanship
• Component failures under normal operating conditions
• Replacement parts for covered defects

Important Warranty Notes:

• Warranty requires proper installation by qualified professionals
• Excludes damage from freezing, running dry, or improper maintenance
• Proof of purchase required for warranty claims
• Extended warranty options may be available – contact retailer for details

💡 Protect your investment: Proper winterization and regular maintenance as described in this guide help ensure warranty validity and extend pump lifespan beyond the warranty period.

🏊 Perfect Pool Sizing Guide

The iFlo 0.75HP pump is ideal for a range of pool sizes. Use this guide to determine suitability for your pool:

✅ Recommended Pool Sizes

Pool Type	Volume Range	Typical Dimensions
Above-Ground Pools	15,000 – 40,000 litres	Up to 5m diameter or 4m x 8m
Small In-Ground Pools	20,000 – 50,000 litres	Up to 3m x 6m x 1.5m deep
Paddling/Plunge Pools	5,000 – 20,000 litres	Various compact designs
Hot Tub Circulation	1,000 – 5,000 litres	Supplementary circulation

💡 Flow Rate Performance

Typical Performance: 8-12 cubic metres per hour (m³/h) depending on system resistance

Turnover Time Examples:

• 20,000L pool = Complete circulation in approximately 2-3 hours
• 30,000L pool = Complete circulation in approximately 3-4.5 hours
• 40,000L pool = Complete circulation in approximately 4-6 hours

⚠️ Note: Actual flow rates depend on pipe diameter, length, fittings, filter type, and total system head. Industry standard recommends complete pool turnover every 6-8 hours.

🎯 Ideal Applications

✅ Primary Filtration Systems

Perfect as the main circulation pump for small to medium residential pools. Provides consistent flow through sand, cartridge, or DE filters.

✅ Above-Ground Pool Systems

Ideal power rating for above-ground pool filtration without excessive flow rates that can damage vinyl liners or connections.

✅ In-Ground Small Pools

Cost-effective solution for smaller in-ground installations, plunge pools, and compact swimming pool designs.

✅ Pool Heating Systems

Compatible with electric heat pumps, gas heaters, and solar heating systems. Provides adequate flow for efficient heat transfer.

✅ Water Features

Can power fountains, waterfalls, and decorative water features integrated into pool designs.

✅ Spa & Hot Tub Circulation

Suitable for supplementary circulation in hot tub systems (not for high-pressure jets).

💰 Running Cost Comparison

Understanding your pump’s running costs helps you make informed decisions:

Estimated Energy Consumption

Operating Hours	Daily Cost*	Weekly Cost*	Monthly Cost*	Annual Cost*
4 hours/day	£0.22	£1.54	£6.72	£80.64
6 hours/day	£0.34	£2.38	£10.08	£120.96
8 hours/day	£0.45	£3.15	£13.44	£161.28
12 hours/day	£0.67	£4.69	£20.16	£241.92

Based on 0.56kW power rating and avera

ge UK electricity cost of £0.24 per kWh (November 2025). Your actual costs may vary depending on your energy tariff.

💡 Cost-Saving Tips

✅ Run during off-peak hours if you have a time-of-use tariff (typically 30-50% cheaper)

✅ Optimal runtime is 6-8 hours daily during swimming season – longer isn’t always better

✅ Clean strainer basket weekly – debris increases resistance and energy consumption

✅ Maintain proper water chemistry – extends equipment life and reduces replacement costs

✅ Winterize properly – protects pump from freeze damage, avoiding costly repairs

✅ Ultra-quiet operation means you can run during evenings without disturbing neighbours

🔧 Installation Requirements

📍 Location Guidelines

✅ Minimum 2 metres from pool edge (safety requirement per IEC60364-7-702)

✅ Horizontal mounting only – pump must be level for proper operation

✅ Maximum 3 metres above water level – minimizes priming time and maintains efficiency

✅ Dry, well-ventilated area – protected from rain and moisture

✅ Firm, stable base – reduces vibration and noise for ultra-quiet operation

✅ Easy access to strainer basket – transparent cover must be accessible for cleaning

🔌 Simple Connection System

Standard 1.5″ (38mm) Connections:

• Suction inlet: 1.5″ for main pool water intake
• Delivery outlet: 1.5″ for return to filter system
• Compatible with standard UK pool plumbing fittings
• Universal sizing simplifies installation and replacement

⚡ Electrical Requirements

⚠️ IMPORTANT: Professional installation by qualified electrician required

• 30mA RCD protection mandatory (residual current device)
• All-pole isolation switch required at supply terminals
• H07 RN-F cable specification: 3 x 1mm² minimum
• Equipotential bonding required – connect to pool bonding system
• Minimum 3.5 metres from pool for power supply connection point
• Verify voltage matches pump nameplate before connection

🔌 Pipe Connection Guidelines

✅ 1.5″ pipe connections – standard sizing compatible with most pool systems

✅ Minimize bends and length on suction side – reduces head loss

✅ Use PTFE tape on threaded connections for plastic pipes

✅ Install isolation valves on both suction and delivery sides

✅ Ensure new, clean unions – proper sealing prevents air leaks

✅ No mechanical load on pump – pipes must be independently supported

🚀 Quick Start Guide

Initial Setup (First Use)

1. Pre-Installation Checks

• Verify electrical supply matches pump nameplate
• Ensure pump shaft rotates freely by hand
• Check all connections are clean and undamaged
• Confirm 1.5″ pipe fittings are compatible

2. Priming the Pump

• Unscrew transparent pump lid
• Fill pump body with clean water up to lower suction pipe level
• Screw lid firmly back in place – ensure proper seal

3. Starting Operation

• Open all suction and delivery valves fully
• Start motor and wait for self-priming (may take several minutes)
• Pump is correctly primed when water level is visible below transparent cover
• Check for leaks at all connections
• Confirm ultra-quiet operation – excessive noise indicates issues

4. Normal Operation

• Monitor strainer basket – clean when half full
• Check for unusual noise or vibration
• Verify consistent flow through return jets

⚠️ NEVER operate pump dry – will cause immediate damage to seals and impeller

🛠️ Maintenance & Care

Regular Maintenance Schedule

Weekly Tasks

✅ Inspect strainer basket – remove debris, clean if necessary ✅ Check for leaks around lid seal and pipe connections ✅ Verify normal ultra-quiet operation – listen for unusual sounds

Monthly Tasks

✅ Clean strainer basket thoroughly – even if not visibly full ✅ Inspect lid O-ring gasket – replace if cracked, compressed, or damaged ✅ Check flow rate – reduced flow may indicate filter or system issues

Seasonal Tasks (End of Season)

✅ Drain pump completely via drain plug (freeze protection) ✅ Clean all components before storage ✅ Store in dry, ventilated area away from chemicals ✅ Inspect motor condition and bearing sounds

🌨️ Winterization Procedure

Critical for freeze protection and warranty validity:

1. Turn off and disconnect power supply
2. Close all suction and delivery valves
3. Open drain plug and allow complete drainage
4. Remove transparent cover and strainer basket
5. Clean and dry all components
6. Store in frost-free location
7. Leave drain plug open during storage

💡 Failure to winterize properly can cause freeze damage, cracking the pump body and voiding warranty.

⚠️ Troubleshooting Guide

Common Issues and Solutions

🔴 Pump Won’t Prime

Possible Causes:

• Air leaks in suction connections – check all unions and seals for tightness
• Lid seal not watertight – clean gasket and lid sealing surface, replace if damaged
• Excessive suction height – lower pump position closer to water level
• No water in pre-filter – fill pump chamber with water before starting
• Incorrect voltage – verify mains voltage matches pump nameplate

🔴 Low Flow Rate

Possible Causes:

• Clogged strainer basket or filter – clean basket and backwash/clean filter
• Suction pipe diameter too small – ensure 1.5″ or larger connections used
• Air entry in system – check all connections for leaks
• Blocked discharge line – inspect filter and return pipework
• Excessive head (resistance) – review system design

🔴 Strange Noise During Operation (Loss of Ultra-Quiet Performance)

Possible Causes:

• Air entry in system – verify all connections are airtight
• Debris in impeller – stop pump, clean strainer, check impeller chamber
• Incorrect mounting – ensure pump is level and firmly secured
• Cavitation from excessive suction lift – lower pump position
• Worn bearings – seek professional service

🔴 Motor Won’t Start

Possible Causes:

• No power supply – check circuit breaker, fuses, and RCD
• Incorrect voltage – verify supply matches nameplate
• Motor thermal protection activated – allow cooling period, check for overload
• Mechanical blockage – check if shaft rotates freely

🔴 Motor Hums But Doesn’t Start

Possible Causes:

• Incorrect voltage or phase – verify electrical supply
• Seized motor bearings – seek professional service immediately
• Impeller jammed – check for debris blocking impeller

⚠️ Safety First: Always disconnect electrical power before any inspection or servicing. For motor-related issues, consult a qualified professional.

❓ Frequently Asked Questions

What size pool is this pump suitable for?

The iFlo 0.75HP pump is ideal for above-ground pools up to 40,000 litres and small in-ground pools up to 50,000 litres. For optimal performance, the pump should circulate your entire pool volume in 6-8 hours. Calculate your pool volume (length × width × average depth in metres × 1000 for litres) and ensure the pump provides adequate turnover.

How long does it take to prime the pump?

Initial priming typically takes 2-5 minutes once the pump chamber is filled with water and the motor is started. If your pump is installed higher than 2 metres above water level, priming may take slightly longer. Ensure all valves are fully open and there are no air leaks in the suction line for fastest priming.

What pipe size do I need for installation?

The pump features standard 1.5″ (38mm) suction and delivery connections. Use 1.5″ or larger diameter pipes throughout your system to prevent flow restriction. Most UK pool systems use 1.5″ or 2″ pipe, making the iFlo compatible with existing plumbing in most installations.

How quiet is this pump really?

The iFlo is engineered for ultra-quiet operation significantly quieter than standard pool pumps. The heavy-duty air-cooled motor features advanced vibration dampening and balanced components. When properly installed on a firm base, noise is minimal – comparable to a quiet refrigerator. You can run it during evenings without disturbing your household or neighbours.

Can I use this pump with a saltwater pool?

Yes, the iFlo pump’s thermoplastic construction is suitable for saltwater pools. However, ensure proper water chemistry is maintained and rinse external surfaces periodically to prevent salt build-up. The pump body and impeller are designed to resist corrosion from pool chemicals including salt systems.

How often should I clean the strainer basket?

Check the strainer basket weekly during the swimming season. Clean it whenever it’s half full or when you notice reduced flow at your return jets. In autumn when leaves are falling, you may need to clean it 2-3 times per week. A clogged basket reduces efficiency and can strain the motor.

What warranty does this pump have?

The iFlo pump includes comprehensive warranty coverage: 2 years on the pump body, 1 year on the motor, and 1 year on the pump seal. This protection covers manufacturing defects and component failures under normal use. Proper installation and maintenance (including winterization) are required for warranty validity.

Is professional installation required?

Yes, for electrical connections. A qualified electrician must install the electrical supply, RCD protection, and equipotential bonding to comply with safety regulations (IEC60364-7-702). The plumbing connections are straightforward with standard 1.5″ fittings, but electrical work must be professionally certified for safety and insurance purposes.

Can I run the pump 24/7?

While the pump can physically run continuously, it’s not necessary or cost-effective. Most pools only require 6-8 hours of circulation daily during the swimming season. Running 24/7 significantly increases electricity costs (approximately £161/year vs £643/year) without proportional benefit. Shorter runtime also extends pump motor lifespan.

What happens if the pump runs dry?

Never run the pump dry – it will immediately damage the mechanical seal and can overheat the motor. If the pump loses prime or runs without water, turn it off immediately. The thermal protection should prevent motor burnout, but seal damage can occur within seconds. Always ensure proper water level and prime before operation.

How long will this pump last?

With proper maintenance, cleaning, and winterization, the iFlo pump typically provides 5-10 years of reliable service. Key factors affecting lifespan include: regular strainer basket cleaning, proper water chemistry, protection from freezing, running time per day, and quality of installation. The pump’s proven reliability and robust construction contribute to exceptional longevity.

Can I use this pump with my pool heater?

Yes, the iFlo 0.75HP pump is compatible with pool heating systems including electric heat pumps, gas heaters, and solar heating panels. The flow rate is appropriate for efficient heat transfer. However, verify your heater’s minimum and maximum flow requirements – most heaters specify required GPM/m³h ranges for optimal operation.

📥 Downloads & Documentation

📄 Product Documentation

📄 iFlo Pump Product Leaflet (opens in new tab)
Quick-reference product specifications, key features overview, and benefits summary. Perfect for comparing specifications before purchase.

📄 iFlo Pump Complete Instruction Manual (opens in new tab)
Comprehensive 8-page owner’s manual including detailed installation instructions, electrical wiring requirements, pipe connection guidelines, starting procedures, maintenance schedule, winterization steps, complete troubleshooting guide, and safety information. Essential reading before installation.

✅ Why Choose the Plastica iFlo Pump?

Proven Reliability

With a virtually zero failure rate and thousands of successful installations, the iFlo has earned its reputation for dependability. When you need your pool pump to work reliably, season after season, the iFlo delivers proven performance.

Outstanding Value

Get professional-grade pool circulation for less than half the cost of premium brands. No compromise on quality, reliability, or performance – just smart engineering and efficient manufacturing keeping costs down.

Simple Installation

Standard 1.5″ suction and delivery connections fit seamlessly into most pool systems. Clear instructions, accessible components, and straightforward plumbing make installation quick and hassle-free for professionals and experienced DIYers.

Ultra-Quiet Operation

Advanced motor engineering and vibration-dampening design deliver whisper-quiet performance. Run your pump during evenings without disturbing your outdoor living space or neighbours – a feature premium pumps charge hundreds more for.

Easy to Own

Simple maintenance, quick-access strainer basket, transparent cover for easy inspection, and straightforward winterization make the iFlo pump hassle-free. Spend less time maintaining equipment and more time enjoying your pool.

Built for the Long Haul

Heavy-duty motor construction, robust thermoplastic casing, chemical-resistant components, and comprehensive warranty coverage ensure years of trouble-free operation. This isn’t a disposable pump – it’s an investment in reliable pool circulation.

Perfect Sizing

Goldilocks power rating – not too weak, not oversized – the 0.75HP delivers optimal circulation for small to medium pools without excessive energy consumption or unnecessary flow turbulence.

🏆 Summary

The Plastica iFlo 0.75HP Pool Pump combines affordability, proven reliability, and efficient performance in a compact, durable package. Purpose-built for swimming pools, it delivers consistent circulation and filtration to keep your pool water crystal clear and inviting.

Key Advantages:

• ✅ Proven Reliability – Virtually zero failure rate for peace of mind
• ✅ Outstanding Value – Less than half the price of comparable pumps
• ✅ Simple to Install – Standard 1.5″ connections fit most systems
• ✅ Ultra-Quiet Operation – Won’t disturb your outdoor living space
• ✅ Heavy-duty air-cooled motor built to last
• ✅ Self-priming design for easy operation
• ✅ Oversized strainer basket for less frequent cleaning
• ✅ Comprehensive Warranty – 2-year pump body, 1-year motor & seal
• ✅ Perfect for above-ground and small in-ground pools
• ✅ Low running costs – approximately £80-160 annually

Perfect for: Above-ground pools, small in-ground pools, pool heating systems, water features, and residential pool circulation applications up to 50,000 litres.

Get professional-grade pool circulation without the premium price tag. The iFlo pump delivers reliable, efficient performance season after season – backed by comprehensive warranty protection.