⚡ Certikin iSAVER-X Pool Pump Frequency Inverter

Transform Your Single-Speed Pump into Variable Speed – Control Flow Rates & Run Times with Touch Screen Technology 🎛️

📋 Product Overview

The Certikin iSAVER-X is a frequency inverter designed to reduce the running costs of pool circulation pumps and improve the efficiency of swimming pool filtration. Swimming pool pumps invariably run at higher flow rates than necessary—with an iSAVER-X you can control both pump flow rates and pump run times.

The iSAVER-X features touch screen control and can be used with permanent split capacitor single-phase pool pump motors. The device allows users to set up to 4 timers for daily operation, each with an individual speed setting. The easy-to-read display shows current operational settings including rpm, power consumption, and timer information.

⭐ Key Features

✅ Touch Screen Control Panel – Easy-to-read LCD display with intuitive button controls

✅ 3 Speed Modes – Night (Low), Day (Medium), and Backwash (High) pre-set speed ranges

✅ 4 Programmable Timers – Set different speeds for different times of day

✅ Speed Range 1200–2900 rpm – Adjustable in 50 rpm increments

✅ Power Consumption Display – Real-time wattage shown on screen

✅ Automatic Self-Priming – Runs at 2900 rpm for 1 minute on startup (adjustable to 10 minutes)

✅ Power-Off Memory – Operation state resumes after power restoration

✅ Wall Mounted Installation – Compact design with mounting hardware included

✅ Ventilation & Fan Cooling – Built-in thermal management

✅ CE Approved – European conformity certified

🔧 Technical Specifications

iSAVER-X 1100 (Single-Phase Pump Output)

Specification	Value
Model	iSAVER-X 1100
Input Power	1 phase AC
Input Voltage	220–240V
Input Frequency	50Hz
Output Power	Max 1.1 kW
Output Voltage	1ph, 0–240V
Pump Type	Single phase
Max Current	6A
Speed Range	1200–2900 rpm
Cooling	Ventilation and Fan cooling
Dimensions (L×H×W)	222 × 117 × 166 mm

🎚️ Speed Modes

Mode	Speed Range	Default Speed
Night (Low)	1200–1650 rpm	1400 rpm
Day (Medium)	1700–2400 rpm	2000 rpm
Backwash (High)	2450–2900 rpm	2900 rpm

⚙️ Parameter Settings

Parameter	Description	Default	Range
1	Priming time	1 minute	0–10 min (1 min increments)
2	Minimum RPM	1200 rpm	1200–2000 rpm (100 rpm increments)
6	Self-priming speed	2900 rpm	1200–2900 rpm (100 rpm increments)

⚠️ Compatibility

Compatible with:

• Pool pumps with permanent split capacitor motors (single-phase)

NOT compatible with:

• Single (Three) phase motors with centrifugal switch
• Pool pump motors with start relays or switch
• Series or DC motors
• Pool pump motors with faults in their rotors or capacitors
• Shaded-pole asynchronous motors

Important: If you are not sure of the compatibility of your pool pump with this device, please contact your supplier or manufacturer before proceeding with installation.

🛠️ Installation Requirements

Environmental Conditions:

• Ambient temperature: -10°C to +40°C
• Relative humidity: 45–90% (non-condensing)
• Altitude: Less than 1000m above sea level
• Keep out of direct sunlight
• Good ventilation required

Electrical Requirements:

• An RCD with rated residual current not exceeding 30mA must be used
• Total cable length (device output + pump cable) should not exceed 2m
• Do not use extension leads

Installation Notes:

• Only ONE pump can be connected to the inverter
• Do not connect any other appliance to the output
• Wall mounting hardware supplied
• For iSAVER-X 1100C, connect pump motor with delta connection

🚨 Protection & Error Codes

Code	Description
E001	Abnormal input voltage
E002	Output over current
E101	Heat sink over heat
E102	Heat sink sensor error
E103	Master driver board error
E201	Circuit board error
E202	Master board EEPROM reading failure
E203	RTC time reading error
E204	Keyboard EEPROM reading failure
E205	Communication error
AL01	High-temperature warning and speed reduction

Note: AL01 is a warning—the inverter will automatically switch to lower speed to self-protect. When temperature drops to 68°C, it resumes preset speed.

📥 Downloads & Resources

📄 Certikin iSAVER-X Brochure – Product overview and features (PDF)

📄 Certikin iSAVER-X Installation & Operation Manual – Complete installation instructions, wiring diagrams, and programming guide (PDF)

🏆 Why Choose Certikin iSAVER-X?

✅ Touch Screen Interface – Modern, easy-to-use control panel

✅ 4 Programmable Timers – Automate pump operation for different times of day

✅ Real-Time Power Display – Monitor energy consumption

✅ Adjustable Speed Control – Fine-tune in 50 rpm increments

✅ Automatic Self-Priming – Protects pump on startup

✅ Built-In Thermal Protection – Automatic speed reduction on overheating

✅ Power-Off Memory – Settings retained during power outages

✅ Compact Design – 222 × 117 × 166 mm wall-mounted unit

✅ CE Approved – European safety certified

🛒 Why Buy From Parts4Tubs?

✅ Authorised Certikin Distributor – Genuine products with manufacturer support

✅ Technical Expertise – Assistance with pump compatibility queries

✅ Competitive UK Pricing – Trade pricing available

✅ Fast UK Delivery – In-stock items dispatched promptly

✅ Installation Support – Help with wiring and setup questions

✨ Summary

The Certikin iSAVER-X Frequency Inverter enables control of pool pump flow rates and run times through touch screen technology. Compatible with permanent split capacitor single-phase motors, it offers 3 speed modes (1200–2900 rpm), 4 programmable timers, real-time power consumption display, and automatic self-priming. The compact 222 × 117 × 166 mm unit features wall mounting, fan cooling, built-in thermal protection, and CE certification. Available in single-phase output (1100) and three-phase output (1100C) versions, both with 1.1 kW maximum output power.