♨️ Aqua-Flo by Gecko XP2e Spa Pump – 3.0HP 1-Speed
Maximum power single-speed performance for demanding high-flow spa jet systems
💧 Product Overview
The Aqua-Flo by Gecko XP2e 3.0HP Single-Speed Pump is the powerhouse of the XP2e range, engineered for high-flow spa applications where maximum jet performance is essential. Delivering an impressive 3.0 HP (2.2 kW) of motor power at 2,850 RPM, this pump produces flow rates up to 680 L/min, making it capable of driving multiple hydrotherapy jets simultaneously.
Built around a robust 56-frame motor with Class F thermally protected insulation, the XP2e 3.0HP features a centre suction with side discharge configuration and a rotatable wet end for versatile installation options. The larger frame size accommodates the higher power output while maintaining the proven Aqua-Flo reliability that spa manufacturers depend upon.
With 2-inch suction and discharge ports providing excellent water throughput, this pump is the ideal choice for larger spas, swim spas, or any installation requiring serious jet power. The pump is supplied without a power cord, allowing installers to use existing 3-core cabling for straightforward replacement. Operating at 230V / 50Hz with a 10.3 A current draw, the XP2e 3.0HP delivers the ultimate in single-speed jet pump performance.
✨ Key Features
✅ 3.0HP Single-Speed Motor – Delivers 2.2 kW of maximum jet power at 2,850 RPM
✅ 56-Frame Construction – Larger motor frame for high-power applications
✅ 680 L/min Flow Rate – Exceptional throughput for multiple jet operation
✅ Class F Thermal Protection – Motor insulation rated for demanding operation
✅ Centre Suction / Side Discharge – Efficient hydraulic design for optimal flow
✅ Rotatable Wet End – Adjustable discharge orientation for flexible plumbing configurations
✅ 2″ x 2″ Plumbing – Standard 2-inch suction and discharge ports
✅ Multi-Jet Capability – Powers multiple jets per pump for intense hydrotherapy
✅ Direct XP2 Replacement – Compatible with older XP2 model installations
✅ Proven Reliability – Aqua-Flo by Gecko quality trusted worldwide
🔧 Technical Specifications
| Specification | Value |
|---|---|
| Pump Type | Single-Speed Massage Pump |
| Brand | Aqua-Flo by Gecko |
| Model | XP2e |
| Motor Power | 3.0 HP / 2.2 kW |
| Speed Settings | Single Speed |
| Amperage | 10.3 A |
| Motor Speed | 2,850 RPM |
| Maximum Flow Rate | 680 L/min |
| Voltage | 230 V |
| Frequency | 50 Hz |
| Frame Type | 56 Frame |
| Motor Insulation | Class F Thermally Protected |
| Plumbing Size | 2″ x 2″ |
| Suction Port | 2 inch (Centre) |
| Discharge Port | 2 inch (Side) |
| Wet End | Rotatable |
| Length | 427 mm |
| Width | 203 mm |
| Height | 241 mm |
| Electrical Connection | No cord supplied (use existing 3-core cable) |
⚡ Electrical Requirements
| Electrical Specification | Requirement |
|---|---|
| Supply Voltage | 230 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Full Load Amps | 10.3 A |
| Motor Insulation | Class F |
| Thermal Protection | Yes |
| Connection Type | Hardwired (3-core cable) |
| Power Cord | Not supplied |
⚠️ IMPORTANT:
All electrical work must be carried out by a qualified electrician in accordance with UK wiring regulations (BS 7671). Hot tubs require RCD protection (30mA). This pump draws 10.3 A – verify your spa pack and circuit can supply this current before installation. The pump is supplied without a power cord; existing 3-core cabling can be reused.
🔄 Compatibility Guide
Frame Dimensions:
| Frame Type | Description |
|---|---|
| 48 Frame | Compact spa pump standard (130mm diagonal bolt pattern) |
| 56 Frame | Larger motor frame (147mm diagonal bolt pattern) |
This Pump:
📍 Frame: 56 Frame (larger than 48-frame models)
📍 Plumbing: 2″ x 2″
📍 Suction: 2 inch Centre
📍 Discharge: 2 inch Side
📍 Wet End: Rotatable for flexible installation
📍 Dimensions: 427 × 203 × 241 mm
Replacement For:
This XP2e model is a direct replacement for older XP2 pumps in the 3.0HP class. Verify frame size (56 frame) and plumbing connections match your existing installation.
Compatible With:
The Aqua-Flo XP2e 3.0HP is designed for spa systems requiring high-power single-speed jet operation with 2-inch plumbing and 56-frame mounting. Suitable for various spa brands requiring this specification.
🔌 Installation Requirements
Mounting:
| Requirement | Specification |
|---|---|
| Mounting Position | Horizontal |
| Frame Type | 56 Frame |
| Base | Solid, level, vibration-dampening surface |
| Ventilation | Adequate clearance for motor cooling |
| Access | Sufficient space for plumbing and electrical connections |
Plumbing:
| Connection | Size | Position |
|---|---|---|
| Suction Port | 2 inch | Centre |
| Discharge Port | 2 inch | Side |
Electrical Connection:
| Requirement | Specification |
|---|---|
| Cable Type | 3-core (not supplied) |
| Recommended Cable Size | 2.5 mm² minimum |
| Circuit Protection | 16 A MCB recommended |
Installation Notes:
⚠️ Pump must be installed below water level (flooded suction) to ensure proper priming
⚠️ Never run pump dry – causes immediate seal damage and motor overheating
⚠️ Wet end can be rotated to adjust discharge direction for your plumbing layout
⚠️ Ensure proper bonding to earth as per BS 7671 regulations
⚠️ Power cord not supplied – use existing 3-core cable or install new appropriate cabling
⚠️ 56-frame pumps are physically larger than 48-frame – verify space availability
🛠️ Maintenance Guide
Routine Maintenance:
| Task | Frequency | Notes |
|---|---|---|
| Check for leaks | Monthly | Inspect around seal plate and union connections |
| Inspect unions | Monthly | Tighten if any weeping is detected |
| Check motor ventilation | Quarterly | Ensure motor vents are not obstructed |
| Inspect mounting bolts | Quarterly | Tighten if vibration has loosened them |
| Verify amperage | Annually | Should read approximately 10.3 A under normal load |
| Clean strainer basket | As needed | Remove debris from filtration system |
Warning Signs – Replace Pump If:
- Unusual noise such as grinding, screeching, or humming
- Water leaking from the seal plate area
- Motor repeatedly trips the circuit breaker
- Noticeably reduced water flow to jets
- Motor overheating or cutting out on thermal protection
- Excessive vibration during operation
Seal Replacement:
📍 Contact Parts4Tubs for compatible seal kits for the Aqua-Flo XP2e range
⚠️ Replace seal at first sign of leakage to prevent motor damage
⚙️ Ideal Applications
| Application | Suitability | Notes |
|---|---|---|
| ♨️ Hot tub jet pump | ✅ Yes | 3.0 HP ideal for multiple jet configurations |
| ♨️ Large spa systems | ✅ Yes | 680 L/min supports demanding installations |
| 🛁 Swim spa jets | ✅ Yes | High flow suitable for swim spa jet systems |
| 🔄 Circulation pump | ❌ No | Use dedicated circ pump for 24/7 filtration |
❓ Frequently Asked Questions
Q: What horsepower is this pump?
A: This is a 3.0 HP (2.2 kW) single-speed massage pump running at 2,850 RPM – the most powerful in the XP2e range.
Q: What flow rate does this pump deliver?
A: Up to 680 L/min, making it capable of powering multiple hydrotherapy jets simultaneously.
Q: Will this fit my hot tub?
A: This pump has a 56-frame motor (larger than 48-frame) with 2-inch suction and discharge ports. Check your existing pump’s frame size and plumbing connections for compatibility.
Q: What voltage does this pump require?
A: 230V / 50Hz single phase. All electrical installation must be carried out by a qualified electrician to BS 7671 standards.
Q: Does this pump come with a power cord?
A: No, the pump is supplied without a power cord. This allows installers to reuse existing 3-core cabling or install new appropriate cabling as required.
Q: What size are the plumbing connections?
A: 2 inch on both suction (centre) and discharge (side) ports.
Q: Can I rotate the wet end?
A: Yes, the wet end is rotatable to allow the discharge port to be positioned to suit your plumbing configuration.
Q: What are the dimensions?
A: Length: 427 mm, Width: 203 mm, Height: 241 mm. Note this is physically larger than 48-frame pumps due to the 56-frame motor.
Q: Is this a replacement for older XP2 pumps?
A: Yes, the XP2e is designed as a direct replacement for older XP2 models in the same power class.
Q: How do I know if my pump needs replacing?
A: Common signs include unusual noises, water leaking from the seal area, reduced jet power, or the motor tripping the breaker repeatedly.
🏆 Why Choose the Aqua-Flo XP2e 3.0HP
✅ Maximum Power – 3.0 HP delivers the strongest jet performance in the range
✅ High Flow Rate – 680 L/min supports multiple jets simultaneously
✅ Trusted Brand – Aqua-Flo by Gecko quality recognised worldwide
✅ 56-Frame Motor – Robust construction for demanding applications
✅ Class F Insulation – Thermally protected for reliable operation
✅ Flexible Installation – Rotatable wet end adapts to your plumbing
✅ Direct Replacement – Compatible with older XP2 installations
🤝 Why Buy From Parts4Tubs
✅ UK-based company with local expert support
✅ Fast UK delivery – same day dispatch on orders placed before 2pm
✅ Expert advice from dedicated spa specialists
✅ Competitive pricing on quality spa parts
✅ Full warranty support
✅ Easy returns within 30 days
✅ Replacement seals and parts available
✅ Genuine Aqua-Flo by Gecko products
💫 Summary
The Aqua-Flo by Gecko XP2e 3.0HP Single-Speed Spa Pump is the ultimate choice for high-flow spa applications demanding maximum jet power. Delivering 3.0 HP (2.2 kW) at 2,850 RPM with flow rates up to 680 L/min, this 56-frame pump powers multiple hydrotherapy jets with ease. Class F thermal protection, rotatable wet end, and 2-inch plumbing connections ensure reliable performance and flexible installation. As a direct replacement for older XP2 models, the XP2e maintains trusted Aqua-Flo quality in a robust package. For spas, swim spas, or any installation requiring serious jet performance, the XP2e 3.0HP delivers exceptional results.




